Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Blog Article
Do you find yourself trying to locate suggestions concerning How to Install a Bathtub Yourself?
Installing a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately hard task. If the old bathtub is easily available, the project can relocate immediately; if you need to open a wall to get rid of the old bathtub as well as position the new bath tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will need an assistant to leave the old tub and embeded in the new one. See to it you have actually certified yourself for the task and are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed project, it is better to take into consideration using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new bath tub in your shower room if you have already acquired a brand-new tub and also do not need to change the setup of your previous water system pipes.
Your devices and also material checklist must comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite bothersome due to the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly come from the pipes. When the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before carrying on to fit the new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub until the spirit level reviews degree.
To mount faucets, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; then do the very same for the various other faucet.
Turn on the supply of water and examine all joints and also new pipework for leaks and tighten them if essential. Load the tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub should wait till the tub has been made use of a minimum of once as this will certainly resolve it into its last setting.
Preparing for the Installment
First of all, the supporting structure supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use every one of the provided washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall between the bathroom and also the tiling, resulting in issues with wetness and possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to allow for the motion experienced when the tub remains in usage. The sealer can fracture rather early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very inquisitive about Tools You Need to Install a New Bathtub and I really hope you appreciated the blog posting. Sharing is nice. You never know, you may just be doing someone a favor. Many thanks for going through it.
Book Now!
Report this page